The manufacturer of this, Weihrauch, actually is quite highly thought of, making high quality air guns, and some cartridge arms.

are regarded as 'disposable' guns and I won't work on one, even just to clean. Good luck on your project, but in the trade such guns as this, Davis, Raven, etc. Sarge, my memory may be off, but I think the frame is of some aluminum or 'pot metal' alloy.

Apparently the part I have is the triggerguard, and the part I am after is the frame. Look astonishingly like the Arminius, except it's 9 shots, vice 8. Check the parts diagram link on this page. I may have a chance to get a High Standard Sentinal. Apparently the same revolver, but this time with a different name, and markings. Can anyone either tell me where I can get an 'outer frame' very inexpensively or, give me some dimensions so I can give make one a shot?.ДЄnd here a view from the top rear. 12 Trams [prtjebe fur 22, 13 locking pin fur 12, 13a feather/spring fur 12, 14 cock protection, 15 locking pin fur 14, 16 trigger spring, 17 Locking pin fur 16, 18 barrier fur drum 22, 19 locking pin fur 18, 20 feather/spring fur 18, 21 hinge screw fur 43, 22 drum, 23 ejector fur 22, 24 Driving spindle fur 22, 25 feather/spring fur 24, 26 locking bush fur 24, 27 annular spring fur 24, 28 VerschluB Schiehchulse fur 24, 29 feather/spring fur 28, 30 Kopthulse fur 24, 31 locking pin fur 30, 32 firing pins, 33 mother fur 32, 34 impact plate fur 32, 35 locking pin, 3mm fur 41, 36 locking pin 2.5mm fur 41, 37 locking pin fur 1, 38 retaining screw fur 39a/39b, 39a Buldog grasp, 39b standard grasp, 41 grasp stucco with Abzugsbugel, 42 going from frameworks, 54 swivel arm fur 22, 59 Firing pin protection 2a retaining screw fur 2nd 3 cock (hammer), 4 cock tongue, 5 locking pin fur - 5a feather/spring fur 4, 6 locking bush fur 3, 7 Driving bar fur 8.8 impact feather/spring fur 3, 9 plant sheet metal fur 8, 10 departure (Printers), 11 locking pin fur 1. A tent oaths Refresh Laud 2 1/2', Run 4', 2 grain. Here is a sorta translation to English, courtesy of Yahoo BabelFish:ДЇig. This is a bit different model, but will give you a better idea of what I'm talking about. Here is a similar model, shorter barrel, showing the 'outer frame' fitting over the 'inner frame'.ДЄfter a lot of searching, I found a parts diagram - in German. You can see it's a 8-shooter, and the action works well in double and single action. If I have to make one, it would be a large help if I can get some dimenions instead of just winging the whole thing.ДЄ different view of the parts.

So I'll either have to buy a outer frame, or make one. 22 revolver apart, for some unknown reason. Looks like some person took a decent, working. There is what I'm calling a 'outer frame' that the barrel pins into, that contains the firing pin, the hole for the cylinder pin, and that the latch fastens on to - this is the missing part. Bore has a spider web in it, but should clean up fine. The front sight is gone, and a small Phillips screw is in one hole. Apparently also called Omega, Liberty, Burgo, and who knows what all else. Seems to be of pretty decent quality, even tho the 'frame' is made of some type of pot metal. Made in Germany, by Weihrauch, and the same model, with changes, is still being made. I seem to have gotten every thing except one part, and possibly a few pins. The other day I got a nice Arminius parts revolver, couldn't pass it up, $14. 22 revolver, Need to buy, or need to make a partД¬lick here to go to this topic on the 'live' site. Home > Main Forums > Ask a Guru > Arminius hw7. This is an archive! Click here to go to the live site.

Arminius hw7 22 magnum revolver